Inside water pressure

Leave a reply

One of the common complaints voiced by RVers is low water pressure coming out of one or more inside faucets. We had that problem recently at the kitchen faucet. All other faucets were great. Swapped out aerator with no change. Thought about just ordering a new faucet head but decided to try one more thing. Removed the faucet head and soaked it in a cup of CLR for several hours. GF greatly assisted the process. She noticed that one end of the faucet head had a valve that didn’t appear to be open. As it was sitting in the CLR she poked at it with one of her kitchen gadgets. Each time she poked a few bubbles came up. After reconnecting and using the faucet for half a day, the pressure is back to normal.

Slide Toppers

Leave a reply

Those of you who have slide toppers already know that they get beat up pretty bad – either driving down the highway or setup in camp during high winds. They typically start tearing at the edges. So you get out the old awning tape or Gorilla tape and seal it up, until the tape dries out. Or the stitching around the poly cord comes undone and you have to resew it. You can extend the life of the topper that way but what you typically don’t see (until you actually remove the topper) are the hundreds of pinholes that have magically appeared.

I’m not sure how much it would cost a mobile tech to replace a slide topper but I was fortunate enough to have one replaced as part of an insurance claim. I took it to an independent repair shop and watched very closely while they were doing it. Turns out it’s not that difficult but an extra set of hands really helps. Just pin the roller tube with a cotter pin so you don’t have to re-tension the spring. About 6 screws later, you’re pulling out the old topper, and seeing all the pinholes.

I also found a great source for new topper material here in the Rio Grande Valley. The material is heavier than the OEM slide topper, the poly cord sewing is top notch and I got it in white instead of the heat absorbing black. I can’t really compare prices but it cost me $104 (in 2023) for a 146″ X 46″ slide topper. If you’re in the market for slide toppers or awnings, check out The Shade Shoppe in Don Wes Flea Market. They can also do the installation although I’m not sure what they charge for that.

Email Problems

Leave a reply

I created a separate area for computer stuff but decided to add this in the regular blog since it’s more likely to affect traveling RVers.

This particular problem certainly won’t impact everyone but if my hard-earned knowledge helps a few folks then it will be worth the effort.

A little background might be helpful. When I started fulltiming there were still many people using AOL (I was NOT one of them). Other folks got their email address from whatever local Internet Service Provider they paid to get connected to the internet (via dial up modem). Since I would be traveling all over the country, this presented a problem. I could either establish an account with a national provider (and change my primary email address) or dial long distance to connect with my local provider to keep my email address. I chose the first option. I purchased a hosting package with a national provider, created a new primary email address and got a few other options, like this web page. I still had to worry about connectivity wherever I went but that problem went away as WiFi became more readily available. Since there would be times when I didn’t have Internet access, I chose to use a local email client so all my emails would be stored on my computer instead of a remote mail server. This system has worked well for over 15 years.

So what’s the problem now? Well, a few months ago we were in an area that had T-Mobile Home Internet. We signed up and it was great. Just $50 a month for blazing fast Internet. Only one piece of equipment to plug into an outlet. When we were ready to leave, we decided to keep the account active until we got to our next location. Bonus! It also worked great at our new location. We had much better bandwidth than with the RV park WiFi. Life was good….until it wasn’t.

I hadn’t made any configuration changes to my email but all of a sudden my outgoing emails started getting blocked by a spam protector. I went through their remediation process and emails started flowing again. Then they started getting blocked again. This time the spam company recommended I make a specific configuration change. That sent me on a wild goose chase that lasted hours. The actual problem was the IP address being provided to me by T-Mobile Home Internet. Someone else had abused that address previously and got it blacklisted.

I can’t force T-Mobile to do anything but I have options again. I can still send email through my webmail instead of the local email client. Or, I can connect through a different WiFi and still use Thunderbird. I may even be able to reboot the Home Internet box to try to get a new IP address assigned. I’ll test that later.

UPDATE: The reboot of the Home Internet box worked. I got assigned a new public IP address that was not on a block list. Ain’t DHCP grand? Also, even though this article talks about T-Mobile Home Internet I suspect it could also apply to RVers using Starlink.

Last CamperForce job?

Leave a reply

After all the recent maintenance costs it was great to build up the bank account again while getting our campground partially reimbursed. This was HOU2’s first year with CamperForce, and it showed. I won’t go into all the gory details but it didn’t take more than a few days to determine that I wouldn’t return to this fulfillment center except in a dire emergency.

Shortly after we left, however, I saw a few posts in the Facebook Amazon Camperforce Community group about the website disappearing. I had no desire to return to Houston but there were other locations that I might have considered so I sent an email to the CamperForce address with the following question: 

Some of us have noticed that the CamperForce webpage no longer exists and CamperForce doesn't even show up in google searches anymore. Is the program being disbanded? It would be nice to know now since many RVers plan their yearly travel based on work availability later in the year.

To their credit they responded within a few days (notable since I emailed on New Year’s Eve). And without further ado, here is their response: 

 Thanks for reaching out.  This is a valid question.  At this time the program is being reviewed for further seasons and a decision will be made soon.

As of 1/23/23, I’m not aware of any further announcements but any search for CamperForce only returns blog entries from people who have worked there previously. Many of us will be disappointed if the program dies an ignominious death. My personal opinion is that it’s going away because the original program manager retired about a year ago and his successors just didn’t support the program like he did.

Bad luck or charmed life?

Leave a reply

We left the PNW allowing plenty of time to get to Houston TX, with good reason as it turns out. We made it precisely 110 miles down the road before pulling into a rest area and noticed smoke rising from the front driver’s wheel well. It didn’t take long to figure out that the brake caliper had seized. I tried taking the tire off to see if I could free the caliper but one of the lug nuts refused to budge past a certain point. Good Sam Roadside Assistance to the rescue. Despite a few miscommunications a very large tow truck arrived a few hours later. We had already reserved a spot at a nearby RV park and Good Sam set up an appointment for us at a nearby Dodge dealer. After a 3 day delay (and new rotors, calipers and pads on the front axle) we were back on the road.

It’s amazing (or not) how much you pay attention to every little sound driving down the road after repairs. Just hoping that nothing else is going to rear its ugly head. But it didn’t. All the way through Oregon, Idaho and into Utah. We rolled the dice on the Hill AFB FamCamp without reservations, mainly hoping for somewhere with great WiFi for a paid interview with User Testing. Well, we got a site for 3 nights and had 2 days before the interview. Naturally, I looked for a Chinese buffet and found a very good one. But while driving through town I noticed some vibration coming from the truck. Damn!! Bright and early Monday morning I drove into town to get it looked at. Surprisingly, they were able to start troubleshooting immediately. The mechanic took it for a short test drive and put it on a lift as soon as he got back. More bad news. The driveshaft was on its last leg. Their first call for a replacement part was the nearby Dodge dealer, where they were informed that the part had been discontinued. They finally tracked one down but it would be several days before it arrived. As I type this, we’re still waiting.

More money for repairs. Bad news. More delay. Bad news. Finding the problems without major accidents? Charmed life. Being in a very safe RV park with full hook ups and shopping within walking distance while we wait? Charmed life. With any luck, the charm will continue and the repairs will be made as quickly as possible and we’ll be on our way again soon.

Random Thoughts from the PNW

Leave a reply

For those who don’t travel much, PNW is the Pacific NorthWest. I’m on my fourth visit to the PNW, third in an RV. Sometime last year, I spotted a campground ad looking for help over the summer and, after some discussion, Mary and I applied for and got the jobs. It looked like fairly easy duty and enough time off to explore the area.

Well, next time, I should probably check Google maps a little better. The initial plan was to spend a lot more time hiking in Olympic National Park. It looked very doable last year but now that we’re here, the driving times are somewhat excessive. This week we planned a trip to the Hoh Rain Forest to get my free veteran’s pass and hike a couple of short trails. Well, besides a 2 hour drive to get there it was the middle of the day and the line of cars to get to the visitor’s center was one and a half hours long. So we turned around and drove another hour plus to the Port Angeles visitor’s center where we were in and out in about 3 minutes. Bonus: Asian Buffet in Port Angeles and a short waterfall hike nearby.

For several months I’ve been reading about the heat wave covering much of the country. Here on the Pacific Coast of Central Washington, we haven’t had that problem. It’s rarely hit the 70s during the day and much chillier at night. At the end of July, the heat pump and a space heater still get daily use. But at least we’re not paying for electric.

And an unexpected bonus. Washington is well known for its apple orchards. A few years ago I became acquainted with a variety called Super Cosmic Crisp. In most parts of the country they’re very expensive. Around here I’ve been able to find them on sale at different stores for $0.99 a pound!! For those of you who haven’t tried them, they’re just as sweet as Honey Crisp but much denser. A good sized Cosmic Crisp can almost be a meal by itself.

And now I have to edit because I forgot all about my bicycle rides. First, it’s great not dealing with high temps while riding. Second, it’s way better than road riding in Texas. Down there I always, always, always had to worry about loose dogs charging me. I had to work on my balance down there so I could keep riding and swing a bicycle lock cable at the same time. Here in Washington the few barking dogs I’ve encountered have been behind fences and closed gates. Maybe as a byproduct of that, there are lots of deer roaming the streets in town (bucks, does and fawns). Today I unexpectedly spooked a black bear. He was very close to the road edge and either heard or saw me approaching. As I passed him he was heading further into the brush, very loudly and quickly.

12 Days, 3000 Miles

Leave a reply

Another long trip is in the books. Over the winter in the RGV, I’d done repairs on both the RV and the truck and we were just hoping for an uneventful trip. HA! said the universe.

It started out well enough. On the first day northbound, I thought there might be a problem with the inverter (necessary to keep the refrigerator running while traveling). By the second day I was 100% certain. After checking breakers and fuses, Mary started calling around to find a new inverter. We found a few places that would work, for a cost of around $200. We made it to our second overnight stop and had to make a decision about the inverter. During the long drive, I had plenty of time to think and finally recalled a similar problem I had a few years ago with the inverter. When we got to the RV park, I completely disconnected the battery connected to the inverter, waited a minute or two, then reconnected it. Lo and behold, the inverter was working again. $$$ and time saved.

On we drove, ever westward. Going across New Mexico on I-40 we started hearing an unusual noise while braking. By the time we got to our scheduled casino RV park stop, it was very noticeable. We’d stopped early enough to start looking for a mechanic. Google is really great but sometimes the listings are real outdated. I called 3 or 4 nearby mechanics. I got voice mail for one and dutifully left a message (they never called back). One said they were very busy but he would check with his boss and call me back (he never did). The others came up with invalid numbers. By that time, most businesses were closed. I started looking further away, at a Dodge dealer, and settled on that for my last resort option. I also looked a little closer at the maps and found a few more options in a nearby town. Early the next morning, I called a small shop and they could see me right away. Within 2 minutes of arriving at the shop, me and my truck were on a lift. They’d pinpointed the problem and I had new front brake pads installed in under 30 minutes at a very reasonable price. We did a quick restock at Walmart and stayed another night at the casino just to rest up a little more.

While driving towards Albuquerque the next day we decided to skip one stop in Arizona. Between the price of diesel and the wind direction, it just wasn’t worth it. We did, however, stop at a small native American owned trading post (with RV park) long enough to tour the Grand Canyon for a day and enjoy a couple of good meals in their restaurant.

Now we’re heading northwest, over halfway to our final destination. Made it to our next stop in Utah without problems, although we were getting tired of the monotonous scenery. Because of the short driving day, we unhitched the truck to get some cheaper diesel and a local pizza. This particular park was mostly full of permanent RVers, much like many of the parks we’d stopped at. Getting out of the spot required some thought and consideration but we made it without any scratches. Then about 2 hours later a passing car notified us that we had a problem. Pulled over quickly at the end of an on ramp and walked around the RV. Well, halfway around. That’s all it took to notice a broken spring hanger and 2 tires touching each other. This was the same spring hanger that just got rewelded in San Antonio last December. Good Same Roadside Assistance was worthless in this situation. I Googled mobile welders and found one nearby (in Ogden) who responded immediately. Looks like he did an excellent job welding the hanger and even stayed to help me reattach the leaf spring. His price was very reasonable and we made it to our next scheduled stop without losing a day.

This should have been our last 1 night stay prior to arrival at our summer gig. We were all looking forward to fully setting up and settling in. We were heading north in Washington when we noticed another strange sound, this one coming from the transmission area. I just had the clutch and flywheel replaced a couple of months ago in Texas so this came as a real surprise. We had to backtrack about 20 miles to a Dodge dealer. After inspecting underneath the truck, they couldn’t definitively diagnose the problem further than a fluid leak. I found a nearby RV park that had room for us and setup there for a night with plans to return to the dealership when they opened the next morning to at least fix the leak. Dropped off the truck the next morning and while walking back to the RV park got another call from them. They admitted a mistake in the source of the leak, needed to order another part that would arrive the next day. That part was the most expensive repair of the trip but it arrived early enough in the day for the truck to be ready to go by noon. They also advised me that the guy in the RGV did NOT install all the parts he charged me for. I’m fighting over that now.

Anyway, after 12 days and 3000 miles, we finally made it safely to Copalis Beach Washington where we’ll settle in until the fall.

Ahhh, the sound of silence.

Leave a reply

Am I talking about a Simon & Garfunkel song? Or maybe camping in the deep woods? No on both counts. I’m talking about the annoying squeak of a bathroom faucet.

When I first got this 5th wheel, all was good. I could turn the hot and cold water faucets all day long and they would not make a single sound. Then the dreaded day came when they both started squeaking. I endured for awhile but it finally got to be too much. I started researching, then removed both handles and applied some plumber’s grease. That corrected the problem for a few months. When the squeaking started again I thought my only option was to buy a new faucet, something a little higher quality than the OEM faucet. Off to the hardware store I went in search of a replacement. I found the proper size, took it back to the RV and installed in under 1 hour.

I heaved a huge sigh of relief when I first tested the handles and heard nothing but running water. I was back in my happy place for over a year. Then these handles started squeaking. Back to the internet for more ideas. I finally determined that I needed to get way down in the guts of the faucet, or just resign myself to buying a new faucet every other year. Since I hate waste and always prefer to repair instead of replace, I got out a few more tools and began the disassembly. I faintly heard Johnny Five (https://en.wikipedia.org/wiki/Short_Circuit_(1986_film)) in the background saying ‘No disassemble’ but I pressed on.

During the disassembly, I narrowly averted disaster – or at least another trip to the hardware store. While holding one of the plastic pieces I heard something pop and saw a small rubber piece roll to a stop on the floor. I had no idea where it came from so I continued to disassemble the other side. Sure enough I found that piece and it had a spring under it. After a minute of searching, I found the other spring on the carpet. I slathered plumber’s grease everywhere I could and hoped for the best. I’m also ashamed to say that I wasn’t very conscientious about positioning of the plastic valves when I took it apart. I took my best educated guess when putting everything back together. Miraculously, when all was said and done, water flowed when and where it was supposed to. No water flowed, or even dripped, where it wasn’t supposed to. And best of all, there was nothing but blessed silence again when turning the handles. Hopefully, this fix will last longer than the last one.

When is my black tank really full?

Leave a reply

Bring up this question online and you’ll get lots of different opinions. Why does it really matter?

Well, it matters because you want a lot of liquid in your tank before dumping to help flush all the solids out. If you dump your black tank on a daily basis, or worse, just leave the black tank valve open, you’ll get the dreaded poop pyramid. All the liquids will drain out and leave the solids. The goal here is to make sure your black tank is over half full before dumping, which takes us back to the original question – when is it really full?

Tank sensors are inaccurate, at least after the first couple of uses. Some people use a set number of days. That might work – after you’ve figured it out some other way but tanks are different sizes and the way people use their toilets is infinitely variable. Some folks just get a feel for it, but verify by shining a flashlight down the toilet pipe. I guess that works but, ewwwww!

I personally wait until my toilet burps back at me. What????? Yes, when you flush your toilet and the tank is full enough to start covering the vent pipe, it will burp at you. You want to pay attention to this when it first starts burping. You really don’t want that to happen after taco Tuesday, if you get my drift. Some folks just can’t visualize a burping toilet so I made a video of it for your viewing pleasure. Feel free to rewind or use slo-mo.

Time for a new category

Leave a reply

After the last few posts, I realized that I need a category for RV maintenance. It seems to be taking up more and more of my time now that the 5th wheel is 5 years old.

After the wet bolt kit upgrade, the next project was (drum roll please) the toilet. It’s actually been an ongoing project for the last few months. For you non-RVers, our toilets are much different. There is no toilet tank holding several gallons of water to push stuff through the pipe. We basically have a 2 piece toilet – the bowl and the base. Between those 2 pieces is a flush valve to allow ‘stuff’ from the bowl to enter a pipe, which leads straight to a holding tank. We flush with a foot pedal. Besides opening the flush valve, it also sprays water into the toilet bowl. When you release the pedal it closes the flush valve and a small amount of fresh water remains in the bottom of the bowl. That small amount of standing water provides a barrier so that odors from the holding tank don’t come back up into the bathroom.

It’s fairly common for RV toilets to develop leaks around that flush valve so the bowl will no longer hold water. I’ve experienced this problem in the past and there are various solutions depending on the cause. Sometimes that opening just needs a thorough cleaning. Someone actually makes a special tool for it. I just use a circular toilet bowl brush. Sometimes a few ounces of vegetable oil in the bowl will recondition the rubber seal and make everything great again. And sometimes you just need to replace the seal. Not a fun job, but also fairly easy.

During my latest problem I tried the cleaning. That fixed the problem for a few days. I tried the vegetable oil. That lasted about a week. I changed the seal. That lasted about 3 weeks. So I started looking at other parts that could be changed. I changed a drive arm and the flush valve itself. Hell, I even tried some FlexSeal paint on the bottom of the bowl. Still no better. I’d been checking YouTube videos for other ideas and looking for more options in online forums. All the forum responses were ‘Buy a new toilet’. I found one YouTube video where the guy did a very good job of documenting 2 parts replacements. At the end of that video, he fessed up that given the same circumstances in the future, he would just buy a new base. That’s all I needed to hear at that point.

I checked online prices and shipping times, then found a local RV dealer that had one in stock for a reasonable price. That afternoon I installed the new base in under an hour (practice makes perfect). And it just felt different when I tested the flush. More solid. I didn’t mention it earlier but this particular toilet has a porcelain bowl but a plastic base. I’m not sure if the plastic got compressed enough to allow the leak or if an O ring just deteriorated. That O ring didn’t show up on any of the parts lists for the toilet but there was a definite difference between old and new. Just in case, I measured it and ordered a few spares for future use. So far so good on water staying in the bowl.